How-to fit late-model wheels on a vintage Mustang...

[Chris]

Fit late-model wheels on a vintage Mustang: an easy-to-install adapter kit allows you to fit 17-inch or larger late-model Mustang wheels on a '65-'73 Mustang. (HOW-TO)(National Parts Depot)


Source: Mustang Monthly

Publication Date: 01/01/2006

Author: Cook, Miles

COPYRIGHT 2006 Primedia Enterprises, Inc.

In our July '05 issue, we showed various 16- and 17-inch wheel sizes that will fit on a vintage Mustang. Regular readers will recall that a number of 16- and 17-inch sizes will fit on most early Mustangs, including 16X8-, 17X8-, and 17X9-inch wheels with 4.5 inches of backspacing.

[ILLUSTRATION OMITTED]

This time we're exploring a similar idea but with a late-model variation because it is possible to fit '94-'04 Mustang wheels on vintage cars.

The straightforward solution is a late-model wheel-adapter kit that's available from National Parts Depot (NPD). If late-model wheels on an early car is a look that interests you, or if you're on the fence as to whether you like it or not, the following photos may help you make a decision.

NPD's adapter kit allows you to fit late-model wheels on a vintage Mustang. The most representative application will be the 17X8-inch wheel used on '94-'04 Mustang GTs, Cobras, and Mach 1s. Shown on our '69 fastback project car is the popular Premium Package wheel available on '01-'04 GTs. Popularly known as the "Bullitt" wheel, it also came on the '01 Bullitt with 245/45ZR17 tires, usually Goodyear Eagle ZR45.

[ILLUSTRATION OMITTED]

While the adapter kit is marketed with these wheels in mind, can be used with any 17X8-inch wheel that came on a '94-'04 GT, '94-'01 Cobra, or '03-'04 Mach 1. This includes more than a half-dozen styles, which are all 17X8-inch with a 4.5-inch bolt circle and 5.72-inch backspacing. Examples include the unique designs on '94-'95 5.0s and Cobras, '96-'97 Cobras, '96-'98 GTs, '98 Cobras, '99-'01 Cobras, '99-'04 GTs (three styles were used, including the '99-'01 Cobra wheel on '03-'04 GTs), and '03-'04 Mach 1s.

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

[ILLUSTRATION OMITTED]

All these wheels look different, but they have the measurements mentioned above and all came with 245/45ZR17 tires, either Goodyear or BFGoodrich (Cobras). Furthermore, these wheels are an easy fit on '67-'73 Mustangs and will also fit on '65-'66s if you're careful with front fender clearances, ride height, and suspension mods.

In addition to showing the adapters with the 17X8-inch wheels they're intended to work with, we also bolted on a set of 18-inch wheels to the same car. Although our '69 fastback project car is too low in the front to run the 18s or fairly large 265/35ZR18 tires, it's possible to have them on a car with a closer-to-stock ride height. For both the front and rear, it might be necessary to roll (or radius) the fenders for added clearance depending on tire size.

[ILLUSTRATION OMITTED]

1 Whatever studs are on your car, the front 1-inch spacers slip right over the car's existing wheel studs.

[ILLUSTRATION OMITTED]

2 Thread the supplied standard lug nuts in place to secure the spacer on the hub ...

[ILLUSTRATION OMITTED]

3 ... and tighten securely with a ratchet and socket. Tighten as if you were installing the wheels on the car. A torque wrench is a good idea, as these lug nuts should be tightened to 70-80 lb-ft. Have someone hold the brake pedal to securely tighten the adapter. The wheel then installs right onto the adapter as normal.

[ILLUSTRATION OMITTED]

4 If your car has the original wheel studs that are threaded all the way to the outside end of the stud, then this issue isn't likely to be a problem. However, if your car (like ours) has replacement studs, you may be limited as to which wheels you can use with the adapters. Many replacement studs have a tapered end (like ours) about 1/8-inch long that's not threaded. This makes the stud stick out past the wheel adapter. If this is the case with your car, use a wheel that has hollow pockets cast into the back of the wheel between the stud holes, which will allow the extra stud length to sit inside the pockets on the wheels. You won't be able to use a wheel that's solid between the adapter's stud holes on the backside of the wheel. The solution would be to either use a different wheel, or if you're intent on using wheels without pockets, install shorter OEM-type studs.

[ILLUSTRATION OMITTED]

5 Luckily, these wheels had the pockets to clear the longer studs for our Baer brakes. Other '94-'04, 17-inch Mustang wheels may or may not have these pockets, so keep this in mind if your car has longer studs with the ends that aren't threaded. The '01-'04 Bullitt wheels (like ours) have the pockets, so if they're your choice, you'll be all set regardless of the type of stud you have on your car.

[ILLUSTRATION OMITTED]

6 There is another set of choices to consider when it comes to the rear wheels. The adapter kit includes a pair of 1/2-inch spacers for the rear wheels as well as 10 longer wheel studs for the rear axles. The kit instructions state the use of the "rear thin adapters is not totally required." We found that to be true: There were no clearance issues with the 17-inch wheel and 245/45ZR17 tire at the back of our car. However, while the wheel and tire did fit, it was spaced too far inside the wheel well and didn't look quite right. The instructions also say that these thinner (1/2-inch) adapters space out the rear wheels so they're correctly positioned to put the rear tires on the same track as the fronts. However, to do this, you'll need to remove the rear axles on your car since the rear studs won't likely be long enough to allow for the adapter to fit between the brake drum (or rotor in the case of our car) and wheel. While replacing the studs is certainly a good choice, for now we're going to keep the car's existing 16-inch wheels in place. This brings us to a third possible solution. As shown in the next photo, we installed a 1-inch front adapter on the rear rotor, which placed the rear wheels just-right inside the rear fenderwell, which is the arrangement we used in the photos of the car with the 17- and 18-inch wheels in place. The only downside is that it requires two adapter kits to have 1-inch spacers with all four wheels. This extra expense is alleviated by not having to install the longer studs.

[ILLUSTRATION OMITTED]

7 The 1-inch adapter bolts directly onto the rear-wheel studs, just like up front. This is a good way to go if you want to avoid installing new studs in your car's rear axles. However, our car has replacement studs due to its Baer brakes, so other studs on a given car might be long enough. Assess each situation on a car-to-car basis, considering factors such as what studs are in place, which brakes you have (OE or aftermarket), what size wheels you want to run, and what track variations you want or don't want between the front and back of your car.

[ILLUSTRATION OMITTED]

text and photos by Miles Cook

National Parts Depot

Dept. MM

900 SW 38th Ave.

Ocala, FL 34474

800/874 7595

352/861-8700

California

800/235-3445

805/654-0468

Michigan

800/521-6104

734/591-1956

North Carolina

800/368-6451

704/331-0900

www.nationalpartsdepot.com

Nitto Tire

See your local Nitto tire dealer.

www.nittotire.com

OE Performance Wheel

Dept. MM

10554 Progress Way

Cypress, CA 90630

866/303-2683

888/432-0555

www.oeperformancewheel.com
COPYRIGHT 2006 Primedia Enterprises, Inc.

[BS Racing]

a 65 GT 5 lug read end will bolt up to a few newer model mustangs.
That's what I picked up to stuff under my II, no adapters req

[DSGGEN2]

^what does this guy kno anyway

[NUTTZ]

what about a 89 honda?

[DSGGEN2]

[BS Racing]

Originally Posted by DSGGEN2

^what does this guy kno anyway

Obviously more than some Moderator